Science Fair Project Encyclopedia

Science Fair Project Encyclopedia Contents Page

Inductor

(Redirected from Ferrite bead)

An inductor is a passive electrical device that stores energy in a magnetic field, typically by combining the effects of many loops of electric current.

Inductors

Contents

1 Physics of the inductor

1.1 Construction
1.2 Inductance
1.3 Energy
1.4 In electric circuits
1.5 Inductor networks

Physics of the inductor

Construction

An inductor is usually constructed as a coil of conducting material, typically copper wire. A core of ferrous material is sometimes used, which increases the inductance. Inductors can also be built on integrated circuits using the same processes that are used to make computer chips. In these cases, aluminum is typically used as the conducting material. However, it is rare that actual inductors are built on ICs; they are bulky on a small scale, and practical constraints make it far more common to use a circuit called a "gyrator" which uses a capacitor to behave as if it were an inductor.

Smaller inductors used for very high frequencies are sometimes made with a wire passing through a ferrite cylinder or bead.

Inductance

Inductance is a physical characteristic of an inductor. See inductance.

Energy

The energy (measured in joules, in SI) stored in an inductor is equal to the amount of work required to establish the current flowing through the inductor, and therefore the magnetic field. This is given by:

$E_\mathrm{stored} = {1 \over 2} L I^2$

where I is the current flowing through the inductor.

In electric circuits

An inductor only resists changes in current. An ideal inductor does not offer any resistance to direct current, except when the current is switched on and off, in which case it makes the change more gradual. However, all real-world inductors are constructed from material with finite electrical resistance, which opposes even direct current.

In general, the relationship between the time-varying voltage v(t) across an inductor with inductance L and the time-varying current i(t) passing through it is described by the differential equation

$v(t) = L \frac{di(t)}{dt}$

When a sinusoidal alternating current (AC) flows through an inductor, a sinusoidal alternating voltage (or electromotive force, abbr. emf) is induced. The amplitude of the emf is related to the amplitude of the current and to the frequency of the sinusoid by the following equation.

$V = I \times \omega L$

where ω is the angular frequency of the sinusoid defined in terms of the frequency f as

$\omega = 2 \pi f\,$

Inductive reactance is defined as:

$X_L = \omega L = 2 \pi f L\,$

where X_L is the inductive reactance, ω is the angular frequency, f is the frequency in Hertz, and L is the inductance.

Inductive reactance is the positive imaginary component of impedance.

The complex impedance of an inductor is then given by:

$Z = j \omega L = j 2 \pi f L\,$

where j is the imaginary unit.

Inductor networks

Inductors in a parallel configuration each have the same potential difference (voltage). To find their total equivalent inductance (L_eq):

A diagram of several inductors, side by side, both leads of each connected to the same wires

$\frac{1}{L_\mathrm{eq}} = \frac{1}{L_1} + \frac{1}{L_2} + \cdots + \frac{1}{L_n}$

The current through inductors in series stays the same, but the voltage across each inductor can be different. The sum of the potential differences (voltage) is equal to the total voltage. To find their total inductance:

A diagram of several inductors, connected end to end, with the same amount of current going through each

$L_\mathrm{eq} = L_1 + L_2 + \cdots + L_n \,\!$

Applications

An inductor is closely related to electromagnets in structure, but used for a different purpose; to store energy in a magnetic field.

Because of their ability to alter AC signals, inductors are used extensively in analog electronics and signal processing, including radio reception and broadcasting. As the inductive reactance X_L changes with frequency, an electronic filter can use inductors in conjunction with capacitors and other components to filter out specific parts of the frequency spectrum.

Two (or more) coupled inductors form a transformer, which is a fundamental component of every national power grid.

An inductor is typically used at the output of a switching regulator power supply. The inductor is charged for a specific fraction of the regulator's switching frequency, and discharged for the remainder of the cycle. This charge/discharge ratio is what drops (or boosts) the input voltage to its new level.

History

In 1885, William Stanley, Jr. built the first practical induction coil based on Lucien Gaulard and John Gibbs ' idea. It was the precursor of the modern transformer.

Synonyms

coil, induction coil, choke, reactor

Categories: Electromagnetic components

Science Fair Project Encyclopedia Contents Page

10-26-2009 08:16:03
The contents of this article is licensed from www.wikipedia.org under the GNU Free Documentation License. Click here to see the transparent copy and copyright details

All Science Fair Projects