Saved science fair projects:

This is a saved copy of the relevant third party website. We save only the first page of every project because we've found that the third party sites are often temporarily down. We do not save all pages of the project because copyright belongs to the third party author.

 
Welcome to Environmental Inquiry: authentic scientific research for high school students  
Header component
spacer

Conducting Reference Toxicity Tests with Lettuce Seeds
The idea behind a reference toxicity test is that the test organism, in this case lettuce seeds, will respond in a predictable manner to varying concentrations of a particular chemical compound. At some threshold concentration, all of the test organisms will be killed (or in this case, none of the lettuce seeds will sprout). In solutions that are more dilute, some level of inhibition will occur in seed germination and/or radicle length. If the concentration is low enough, no response will be detectable.

This is called a dose/response experiment. You vary the dose of a selected compound, then measure the response of the bioassay organism.

Using NaCl
In order to determine whether lettuce seeds provide a good bioassay for salt toxicity, you can conduct a reference test using known concentrations of NaCl (table salt).

First, make a 0.2M NaCl solution by mixing 11.69 g NaCl with enough deionized water to make 1 liter.

Second, label a series of beakers with the following concentrations: 0.2M, 0.1M, 0.075M, 0.05M, and 0.025M. Make up these concentrations from the 0.02M solution using the proportions listed in the following table:

 

  Concentration

  0.2 M NaCl (mL)

  Deionized Water (mL)

 0.2 M NaCl

 100.0

 0

 0.1 M NaCl

 50.0

 50.0

 0.075 M NaCl

 37.5

 62.5

 0.050 M NaCl

 25.0

 75.0

 0.025 M NaCl

 12.5

 87.5

 Control

 0

 100.0

Then, carry out the bioassay:

1. Treat the lettuce seeds in a 10% bleach solution for 20 minutes, then rinse five times with deionized or distilled water. This kills fungal spores that can interfere with seed germination. Note: Tap water can be used if you do not have access to deionized or distilled water, but it will introduce more variability into your experiment because of the varied minerals and other compounds it contains.

2. In each of 18 9-cm petri dishes, place a 7.5-cm paper filter. Label the dishes according to the first column in the following table. Note: Absorbent paper towels or coffee filters can be substituted for the filter paper, as long as they are first shown to be be nontoxic. (Bleached paper may contain dyes or chlorine.)

3. To each petri dish, add 2 ml of the appropriate test solution. In the control dishes, use deionized water as your test solution.

4. To each dish, add 5 lettuce seeds, spaced evenly on the filter paper so that they do not touch each other or the sides of the dish.

5. Place the dishes in a plastic bag and seal it to retain moisture. Incubate the seeds in the dark at constant temperature (preferably 24.5 degrees C) for 5 days (120 hours).

6. At the end of this time, count how many seeds in each dish have germinated, and measure the root length of each to the nearest mm. Look carefully at the plants to make sure you are measuring just the root, not the shoot as well.

Using Other Compounds
To be useful, a bioassay must be sensitive to the types of compound you are interested in evaluating. For example, if you are worried about herbicide contamination of ponds or streams, a bioassay based on seed germination might prove to be more sensitive than one based on death of fish or invertebrates. On the other hand, fish are likely to be much more sensitive than seeds to a compound that is a nerve toxin, for example.

To determine the sensitivity of an organism to a chemical compound, scientists carry out reference toxicity tests. To do this, you measure the response of the organism to a wide range of concentrations of the selected chemical. What concentrations should you use? That of course depends on both the bioassay organism and the chemical being tested. You might want to start by searching through published student reports included on this web site to see whether anyone else has already generated data that would be of use to you.

Before scientists begin an experiment, usually they search through published scientific literature for papers that relate to the procedure they have in mind. If you have access to scientific journals, it would be a good idea to look for papers that report bioassays using the organism and compound you are interested in (see References for example papers). This is a good way to get an idea about an appropriate range of concentrations.

If you can't find any appropriate data, that's ok -- you'll just have to start with a broader range of concentrations to make sure you hit the range that your test organism responds to. (With too high a concentration, the test organisms will all die, or in the case of seeds, none will sprout. With too low a concentration, you will not be able to detect any difference between your samples and your control.) Ideally, you want to test concentrations that cover both of these endpoints plus a range of concentrations in between. Then you will be able to conclude whether your test organism responds in a predictable way to the compound you are testing.

Serial dilutions are one way to set up a broad range of concentrations. For example, suppose you suspect that in a 100 mg/L solution of a selected compound, no lettuce seeds will sprout, and you are interested in narrowing this down to find out the range of concentrations in which germination will occur. You might decide to start with a 10-fold dilution series, testing solutions of 100, 10, 1, 0.1 and 0.01 mg/L. Another possibilitity would be a dilution series in which each solution is half the strength of the previous solution in the series: 100, 50, 25, 12.5, and 6.25 mg/L.

Once you have collected data using an initial set of concentrations, you may find that it would be useful to carry out a follow-up experiment using a more narrow set of concentrations. For example, if none of the seeds sprout at one concentration in your series, and all of them sprout at the next level of dilution, it would make sense to carry out a dilution series between these two concentrations in order to further define the sensitivity of lettuce seeds to your selected compound.

 




Search for more science fair projects
Search science fair projects Browse science fair projects
or Ask the Mad Scientist for help with your Science Project

All Science Fair Projects